How to clean the iron from the burnt fabric

Each hostess once faced with the problem of burnt fabric on the sole of the iron. This phenomenon happens when the temperature is not observed during ironing. The result is one - a spoiled thing and a black raid on the iron. This raises the question of how to clean the surface. Consider the most effective ways to remove soot on the bottom of the thermal device.

Method number 1. Special pencil

1. Turn on the iron in the outlet, set the power to an average level. Wait for the soles to heat up. Then remove the cleaning pencil from the package and rub the surface of the thermal device.
2. The process will not take long, the composition of the cleaning agent will begin to drain with the remains of burning. Remove the remaining dirt with a paper towel.
3. Stick to safety measures. Be careful, the molten composition should not get on the skin, otherwise burns can not be avoided.
4. Also, when applying a pencil on a hot plane, there will be a strong smell. Cleansing product is suitable for removing soot from all types of soles.

Method number 2. Salt

1. The method is considered one of the most budget and effective. Removal of darkening on the sole of the iron can be done in two ways. Be careful, the method can not be applied on irons with Teflon coating.
2. In the first case, distribute 120 gr. of fine salt on a parchment sheet of paper. Heat the iron to the maximum temperature, perform movements with the device forward as you would iron your clothes.
3. In the second case, pour 150 gr. salt in a thin cotton fabric. Heat the thermometer to the maximum, using a bag with a crumbly composition to remove contamination.

Method number 3. Paraffin candle

1. Paraffin candle will help to cope with the coating and a small soot.Wrap the product in cotton fabric, heat the iron to the maximum temperature.
2. Spend a candle on the heated sole thermopribor. Liquid paraffin removes most of the dirt.
3. After that, steam clean the holes in the sole, if any. Such a move will help avoid the appearance of greasy stains during the next ironing of things.
4. When carrying out an operation to clean the iron, pre-lay a paper towel so that hot carbon flows onto it. At the end of the procedure, wipe the sole of the thermal device with a napkin.

Method number 4. Table Vinegar

1. Vinegar is able to rid the iron of fresh soot. To remove lightly soiled soak a cotton scarf in a 9% solution, wipe the slightly warm sole of the iron.
2. A longer purification method is also possible. Liberally moisten a cotton towel in vinegar, put on it the device is not connected to the network. Wait a day, after the expiration date, remove any carbon residue with a paper towel.

Method number 5. Lemon acid

1. For carrying out such a manipulation as a cleaner, a solution based on citric acid is suitable.
2. Dissolve in 300 ml of warm water 80 gr. bulk composition. Repeat the procedure in the same way as with vinegar.

Method number 6. Hydrogen peroxide and ammonia

1. Dilute 30 ml in a small container. hydrogen peroxide and 10 ml. ammonia. Soak a cotton towel in the composition.
2. Remove carbon deposits on a warm soleplate with an impregnated cloth. Be prepared for the sharp smell of ammonia.

Method number 7. Hydroperit and soda

1. When using soda to remove various contaminants, remember that the product is an abrasive and can scratch an unprotected surface.
2. Prepare a mixture of soda and water, resembling mush. Apply the composition to the contaminated iron surface, rub the surface with a cotton towel. Remove the residue with a napkin.
3. Manipulation with the help of hydroperit should be carried out in a ventilated room, such a tool has a pungent odor. Heat the sole of the iron, apply the product in the form of tablets on the places of pollution, in the case as with a cleaning pencil. Dry the residue with a paper towel.

How to clean Teflon coating

To remove the remains of a deposit from a teflon surface, it is worth resorting to special sponges or pencils. Before using one of the tools, study the instructions in detail.

1. Vinegar and essence. A purification option is also possible with an acetic solution. Take precautions, protect your skin with silicone gloves, such a move will help avoid unwanted burns. If we talk about acetic essence, soak a cloth in it, iron the material with a hot iron. The manipulation should be sufficient. Always observe the temperature when ironing things.
2. Solvent. To remove fabric carbon on the sole of the iron, you can resort to the usual paint solvent. Dampen a cotton pad with the chemical composition, clean the place of contamination with it.
3. Foil. The method using foil is no less effective than all the others. Take a thick sheet of foil, spread on a flat board. Set the iron to maximum power, wait until the thermal device is fully heated. Now smooth the aluminum sheet in such a way as if you were ironing a simple thing. Remove residual dirt with a tissue.
4. Powder for brushing teeth. The tool is quite common in everyday life, but few people already brush their teeth. Moisten a cotton swab with water, apply powder to it.Then wipe a warm sole of the iron in places of pollution. This method cannot be applied to ceramic surfaces.
5. Toothpaste and soda. The use of household products will help get rid of old dirt on the metal coating. Mix soda or whitening toothpaste with a little water. Apply the composition to the dirt and rub it well with a sponge. Do not forget, both products have an abrasive structure, they do not fit all types of soles of irons.
6. Laundry soap. To clean the sole of stuck synthetics, heat the surface of the iron to the maximum mark. Rub with soap, then remove contamination with a paper towel. After that, again rub the sole with household soap and wipe with a damp cloth. The method used is suitable for fresh pollution.

How to clean the ceramic coating

1. If you are faced with the problem of a burnt piece of cloth, a kitchen wooden shovel will help to correct the situation. Heat the iron at maximum power, then use a household appliance to gently remove contamination.
2. Then mix in a small container 10 ml.9% table vinegar and 30 ml. warm water. Moisten a cotton towel, wipe the sole of the iron.
3. You can also put a hot iron on the fabric soaked with the composition for a few seconds. Or resort to the help of a nylon washcloth, wiping with it the hot plane of the thermometer, you can achieve the desired result.

Simple and low cost iron cleaning tools

1. Soak a small piece of cloth with hydrogen peroxide, then wipe the area with a scrape. Carry out the procedure on a warm surface.
2. Also a good and effective means is acetone, repeat the manipulations described when using hydrogen peroxide.
3. Dampen a rag from flannel with lemon juice and a few drops of ammonia. Then walk with a wet cloth at the places of pollution.

Practical recommendations for cleaning the iron

1. When buying an iron, carefully read the instructions for use. Perhaps it will indicate how to clean the sole.
2. Before ironing clothes, always pay attention to the fact whether it is possible to iron the thing and at what temperature.
3. After using the thermal device, always wipe the sole of the iron with a damp cloth, clean it from the scale inside.
4. If it came to thoroughly cleaning the soleplate of iron, pay attention to the coating. Carefully carry out all manipulations without scratching the surface.

To clean the sole of the iron in the home is easy, if you follow the practical recommendations and effective ways. The main thing is to choose the appropriate method based on the type of coating. In the future, observe the temperature when ironing things.

Video: how to clean a burnt iron