How to clean the bath of yellow bloom

A clean and well-kept bath is the calling card of a good housewife. But if the bath is full of lime stains and yellow stains - it becomes clear that it has not been cleaned for a long time. But what to do if yellow traces appeared on the white surface of the bath? How to get them out if the usual Chistol doesn't help? In this article, you will learn why yellow traces and lime spots appear on the surface of the bath, as well as learn about the most effective ways to remove them.

Why do spots and stains appear on the surface of the bath?

Indeed, why does some of the baths shine with whiteness, although it has been installed more than a dozen years ago, while others have a relatively new bathtub full of smudges and yellow spots? This may not always be due to inadequate care.

1. Very often, yellow spots appear due to poor water quality.As a rule, the smudges are most often seen where the water flows - that is, at the level of the tap. This happens if the water is high in chlorine. A certain composition of salts is often added to water, which allows it to stay cool for a long time, which is important for centralized hot water supply. That is why hot water is considered technical - it can not be eaten. But for this very reason, traces of yellow smudges appear on the surface of the bath.
2. If there are a lot of calcium and magnesium salts in water, calcareous formations and an obvious deposit appear on the surface of the bath. This is most often observed in regions with very hard water.
3. Sometimes the smudges have a characteristic not just yellow, but a rusty tint. This is due to the fact that water contains a lot of iron and particles of corrosion. This can be observed in homes with old pipes and rusty plumbing systems.
4. An important role is played by and care of a bathroom. If you clean the plumbing surface regularly, you can get rid of any stains and dirt at the initial stage of its development. If the cleaning is rare, the stain eats into the structure of the material and it becomes more difficult to withdraw it.
5. Another reason for the rapid contamination of the bath and the formation of yellow bloom is improper and illiterate care. How often do housewives begin to rub with a frenzy a new acrylic bath with hard brushes in order to clean it from the slightest contamination. And make a big mistake. Such material as acryl is quite sensitive to various abrasive particles and is easily scratched. After such a fierce cleaning, grooves appear on the surface of the bath, in which dirt and debris get stuck even more actively. This leads to the fact that the bath is worse to clean, yellow spots appear faster, the bath looks unpresentable. Therefore, improper care can also be considered one of the main causes of bath pollution.

Summarizing what has been said, it can be noted that poor quality of water, rust in pipes, improper as well as inadequate care of the surface of the material can lead to contamination of the bath. To get rid of yellow stains and stains, you need to take into account the material of the bath.

How to clean a bath depending on its material

Do not use the same cleaner for all surfaces.At best, it may simply be ineffective, at worst, it will spoil the delicate material. Here are the main types of baths, as well as effective means to cleanse them of yellow bloom.

Acrylic
To date, acrylic baths are considered the most popular and sought after. This is due to the large number of positive qualities of this material. First, the acrylic bath is light - it is very convenient during transportation. Secondly, the acrylic bath does not rust. Thirdly, acryl is considered sanitary material - a fungus does not develop on its surface. In addition, acrylic can make any shape of the bath, which is suitable for the design of your room. For the sake of justice, I would like to note the disadvantages of this material. Acrylic is quite fragile, easy to scratch. In order for an acrylic bath to withstand water and the weight of a person, it must be properly installed. Acrylic is a thin material, so the water in the bath cools quickly. This problem can also be solved by proper installation and proper insulation.

It is not difficult to care for an acrylic bathroom. If every day you just rinse the surface of the bath with water from the shower, you are not afraid of any pollution - the stains simply do not hold onto a smooth surface.Acryl can not be cleaned with brushes, tin sponges, cleaners with abrasive particles, etc. Among the cleaners that can clean the yellow marks on the acrylic bath, you can select the cream "Sif", "Triton", "Panivanna". If you are not sure that the product is safe for the surface, apply a small amount on the edge of the bath. If after 10 minutes there are no defects, you can clean the entire surface of the bath.

You can safely clean the acrylic bath with lemon juice. In a glass of warm water, dissolve the juice of one lemon. Take a soft sponge and wipe the bath surface with this composition. Do not use acetone, kerosene or other aggressive substances to clean acrylic, they corrode this material.

Cast iron
Cast iron baths do not give up their positions - they are just as popular as they were 50 years ago. This is not surprising, cast iron is a strong and reliable material, the water in it cools down very slowly, which allows you to enjoy water treatments for a long time. Cast iron baths are very durable, it has been tested for decades. Unlike an acrylic bath, the cast iron does not resonate with the jet and during the set of water does not emit such loud sounds that can be heard throughout the house. The lack of a cast-iron bath is its surface.Over time, the enamel cracks, grows cloudy, may become covered with spots that are difficult to remove. However, this is a completely solvable problem - today, the cast-iron bath is easy to update, covering it with a new enamel. However, care should be taken with a new coating - any blow may cause chipping or cracking.

If the bath is not covered with additional enamel, it can be cleaned by any means, since its natural layer is fired by very high temperatures and is not afraid of various effects. Cast iron baths are perfectly cleaned with various powders based on soda ash, for example, Pemolux, Biolan. Comet, etc.

At home, you can use the most ordinary baking soda. Mix it with a grated soap and clean the surface of the cast-iron bath with a prepared mass. Be sure to wear gloves so that the composition does not corrode the skin.

Steel
Another type of popular bath is steel. Like acrylic, steel baths cool down quickly and make noise when typing water, however, these drawbacks are easily removed with the help of proper installation of the product. Steel baths are short-lived - with improper care, they begin to be covered with corrosion. Steel baths are easy to transport and install - they weigh a little.The bath is cheaper than its acrylic and cast iron counterparts, so steel is an excellent solution for temporary use.

The surface of the steel is coated with special enamel, which is quite sensitive for various powders, brushes and abrasive particles. In addition, the steel bath can not be cleaned with alkaline or acidic compounds. For cleaning, you should use only gentle pastes, creams and gels, on the packaging of which a list of materials is indicated, to which the product is applicable.

Salvage and hydrogen peroxide will help with home remedies. Mix the two ingredients in equal proportions and apply on the old yellow stains. Leave it for a while, and then wash it off with a flannel cloth - there will be no trace of stains.

These are the main types of materials from which modern baths are made. For each of them, you can choose a professional cleaning composition that will eliminate yellow spots and limescale. But if special cleaning products are not at hand - do not despair, you can clean the bath with what you have at home.

How to clean the bath with improvised means

Here are the recipes that will help clean the bath of yellow spots quickly and safely.

1. Dry bleach. It is a powder used for bleaching fabrics and various surfaces. It must be diluted with water so as to obtain a slurry. Apply the composition to a yellow spot and leave for a while. After 10-15 minutes, rinse the surface of the bath with warm water. This tool is especially effective for steel and cast iron baths (without re-coating).
2. Apple cider vinegar and citric acid. This is a delicate, but effective remedy for cleaning acrylic bath surface. Mix apple cider vinegar with lemon juice or citric acid and pour the mixture into a spray bottle. Spray the composition on the surface of the bath and leave for 15 minutes.
3. Lemon. Any spot of small size can be removed with a regular lemon. Cut the citrus in half and lightly salt it. This will allow the juice to go out and give the desired reaction. Simply wipe the surface of the bath with juice or attach the fruit to the stain with a cut. Leave on for 15 minutes, the stain will simply dissolve.
4. Wine vinegar and salt. Vinegar should be slightly heated so that it is more effective. In a glass of warm vinegar, dissolve two tablespoons of salt and moisten the yellow spots with the prepared composition.After 20 minutes, rinse with a soft sponge and plenty of water.
5. Soda and hydrogen peroxide. Clear stained and stubborn stains can be using soda and hydrogen peroxide. Mix the two ingredients so that the slurry turns out. Using a brush, apply the mixture gently onto the stain and leave it on for a few hours. This composition will help to remove even the most difficult spots and dirt.

If all these tools do not help to remove the stain, most likely, it has entered into the structure of the material very deeply. The only solution in this case is the restoration of the bath and covering it with a new layer of acrylic, enamel or other material.

To bath always was clean and snow-white, you need to properly care for it. Clean the bath regularly, it is easier to remove any contamination if it is fresh. Do not use brushes, abrasive scouring powders, metal objects for cleaning, aggressive acids. All this only worsens the quality of your bath and contributes to the appearance of even more serious cracks and dark spots. In the acrylic bath can not soak linen - powder contains special substances that corrode the material with prolonged contact.If possible, wipe the bath dry so as not to leave it wet. And then the product will serve you for more than a dozen years and will look well-groomed.

Video: how to clean the bath to the snow-white state