How to disable the alarm on the machine without a keychain

For most people of modern society, a car is an integral part of life: according to statistics, each of its owners spends about 20 hours a week in it. Sooner or later, some things will appear in the car, in order to prevent their theft, like the car itself, an alarm is set on the car. It works flawlessly due to the simplicity of its device, the main thing is to monitor the battery charge, however, due to some reason, there may be a situation when you need to urgently turn off the alarm without using a key fob (for example, the battery charge has come to an end, or it is completely lost).

There are two ways to disable the alarm without using the car's key fob:

1. Factory transfer of alarm from security mode to emergency, emergency;
2. Coded disabling alarm with a special pin code.

It is very important to know where the special button is located - “Valet”, after pressing which the car’s electronics enter service mode (“Valet” is the servant, the assistant with the English). Using the button is necessary for any method of disarming the alarm. Depending on the make and model of the car, the location of this button varies, but in most cases it is located:

• to the right of the gas pedal or slightly to the left of the clutch pedal;
• in the fuse box or in the immediate vicinity;
• under the steering column, being slightly recessed;
• under the front panel.

Factory way to disable the alarm

Disabling the alarm using the factory method is reduced to the fact that it is necessary to use the combination of the simultaneous pressing of the “Valet” button and a pedal (or a pair of pedals) that was previously installed in the service center. This extremely important information is always clearly spelled out in the instructions attached to the car or the alarm (so when you buy one or the other, it is important to pay attention to it).

If, for some unknown reason, there is no such booklet, then the only way out is to try all the combinations, using all the pedals one after the other, and then three possible pairs of them. The most common combination is to simultaneously press the service button and the clutch pedal.

Tip: to put the car into service mode, you need to hold the button and the pedals for about 10 seconds - that’s what the car’s electronics need to recognize the command.

If the alarm system of the machine through this time produces several short trills with a certain frequency, and the lights of the dimensions synchronously light up and go out, then this means that the shutdown has been made successfully. In this case, the light-emitting diode installed in the car, should go out.

If after the alarm was turned off, the car needed to be started a second time (for example, if it stalled), then you will not need to repeat the described procedure: that the electronics is still in service mode, the alarm program will notify with two or three short periodic messages. sound signals.

Tip: after installing the alarm on your car, it is recommended to try to turn it off several times and turn it on, bringing the action to automatism.In the future, this will help avoid panic in case of emergency.

Coded Disable Alarm

The coded method of turning off the alarm implies pressing the service button a certain number of times (this number is called the "pin code"). The sequence of actions is as follows:

1. Turns on the ignition of the car.
2. The service button is pressed the number of times corresponding to the first digit of the pin-code (for example, if the pin-code is 25, then the button should be pressed twice).
3. Ignition on again.
4. The service button is pressed the number of times corresponding to the second digit of the pin-code (in the given case - 5).

Obviously, such a shutdown method is more individual than the one described earlier, since the pin code can be set manually. So, the maximum value for it is 9999.

Using a coded way to turn off the alarm, cars are often stolen by intruders, since in most cases the pin code set at the factory is a relatively small value. That is why it is desirable to set a complex parameter for a pin code,containing a random collection of numbers (having nothing to do with any dates, etc.).

Features off some alarms

It was repeatedly stated above that the process of removing a car from an alarm for a particular firm is strictly individual, and there is no universal way suitable for each system. Therefore, it makes sense to separately analyze the alarms of certain models.

For Starline A1, A2, A4, A8, A9 models, the shutdown algorithm looks as follows:

• The car opens with a key;
• Ignition is switched on.

In the next 20 seconds, you must have time to press the service button 3 times (4 times - for A8 and A9). After the system counts the indicated time from the moment of starting the engine, it will emit an appropriate sound signal. Then the car can turn off and start up an unlimited number of times.

In the same way, the alarms of Tomahawk, Pantera brand alarms are turned off. Pantera models are different in that before you press the button, you must start the car twice (after the first start it must be shut down).

The Starline A6 model is different in thatthat the pin code is used as a disconnect tool, so in 20 seconds it is necessary to press a button not three times, but a fixed number of times. The process of removing the car from this type of alarm is described above.

Alligator alarms compare favorably with others in that triple input of an incorrect PIN code automatically blocks all vehicle systems for a certain time (usually half an hour), which thus additionally protects the car from being hijacked by attackers, eliminating the likelihood of matching. The principle of disabling the security system does not have any distinctive features, but at the same time, the time when the button is pressed is limited to 10 seconds.

A very peculiar way of moving the alarm system to the off state is offered by Scher-Khan, the essence of which is the need to transfer the vehicle's ignition key to the “On” position from “Lock” for a limited time. So, the Magicar 6 model is one of the safest, because to turn it off you need:

1. After opening the car with the key, transfer the key three times from the locked position to “On” in 4 seconds. Then you need to turn off the car.
2. The ignition is switched on again, and the number of key position changes is the first digit of the specified pin code. The car is turned off again.
3. The described operation should be repeated before all numbers are entered into the system in this way. The buzzer will turn off afterwards, and the side lights will flash twice.

In the case of the Scher-Khan Magicar 6A, you must also wait for permission to enter the next digit. If the key does not turn after starting the engine, you should wait a bit.

Thus, the complete deactivation of the entire alarm system can be performed without the control panel. To do this, you need to remember either a combination of simultaneously pressed pedals and a service button, or a pin code that is recommended to be installed manually. If the key fob does not work, the main thing is not to panic, but to quietly get into the car and confidently carry out the procedure for turning off the system.

Video: how to disable the alarm if there is no connection with the remote control