How to wash the linoleum after repair: useful tips

To clean the linoleum with maximum benefit, you should consider the type of pollution. The long-term practice of specialists at the moment allows you to get rid of trouble without any problems. It is important to choose a targeted remedy depending on the composition of the contamination. If you follow simple instructions, the problem is solved in a few minutes. Consider everything in order.

How to get rid of cement and whitewash

1. If you started a repair, and linoleum does not need to be changed, you need to protect it with newspapers or film. Unfortunately, even such measures are not always 100% effective.
2. Dust and all kinds of waste may stain the coating. Even in small quantities, such pollution will spoil the original appearance of linoleum. Conventional means, unfortunately, unable to cope with the task.
3. Do not despair ahead of time. The initial appearance of the coating can be easily restored, if properly carry out the procedure. The main thing is to follow practical advice and use the recommended tools.
4. Before the start of manipulation, prepare a simple solution of 100 grams. salt in a bucket of hot water. Mix 60 grams to the liquid. household soap shavings. Wash the floor thoroughly with the mixture.
5. The use of hot water is prohibited. Otherwise, heat can destroy the bright color of linoleum. To return the coating to its former state is no longer possible.
6. Some craftsmen stick tape to the linoleum tape. The protective effect of the repair is quite good, but there is a significant risk that the varnish is removed when the tape is peeled off. Scotch tape is glued to the baseboards, if you restore them, you can use this technology.
7. If you do not correct the situation later, dust will stick to the adhesive from the adhesive tape. After a few weeks, an impressive layer of dirt will accumulate that is difficult to remove without consequences. In the extreme case, the plinth will have to be updated.
8. After you have cleaned the floor with the recommended solution, wipe the linoleum with a fresh compound. To do this, change the water and add some potassium permanganate crystals to it. Chemical reagent must be completely dissolved. In the course of the manipulation on linoleum there will be no divorces.
9. If you could not get rid of the problem as described above, it is recommended to clean the floors again with clean water. Only in this case it is necessary to add 50 ml. kerosene.
10. The only drawback is that after the procedure there is a rather unpleasant smell. To get rid of it, prepare a light solution with vinegar. Leave room to air out.
11. After that, thoroughly dry the linoleum. The result is to fix polishing the surface of a wool product. To achieve maximum gloss, a small amount of flaxseed oil should be applied to the fabric. The surface will take primordial appearance.

How to remove foam from linoleum

1. Before puzzling over the removal of already frozen foam, it should be remembered that it is much easier to wash off fresh. Try to continue to prevent such an outcome of events.
2. To date, there are a lot of professional-oriented funds that employees of cleaning companies successfully use. With the help of such cosmetics you can easily remove the foam from the linoleum.
3. First, try to cut off the “cap” of the frozen foam with a stationery knife, then soak the remaining stain with a choice of “Wa-Lin”, “MELLERUD”, or “San-Wedge”. Proceed with the instructions, do not exceed the specified period of exposure. Then wash the surface with water and dry.
4. There are also special tools that dissolve the frozen construction foam. They can be purchased at building markets or stores of the appropriate orientation. Among these compositions, choose one of the following: “Cosmofen”, “Penosil”, “Bartons Son-off”. Carefully read the instructions before use.
5. In the fight against the frozen foam, follow clear rules. Do not attempt to remove the composition with acetone, industrial solvent or alcohol. All your actions will lead to even greater hardening and absorption of foam in linoleum.
6. Even if at first it seems that everything has disappeared, after drying, dull stains will appear on the surface, which will be strongly evident. The same effect is observed on the laminate.

How to get rid of primer stains

1. If the stains from the primer fresh, remove this kind of pollution is not difficult. To do this, resort to using a soft cloth. Collect the solution with the product, then wash the coating. If the composition had time to harden, the procedure becomes more complicated.
2. The method of removing primer from linoleum is similar to removing foam. Before washing it, the top layer should be carefully scraped off. After that, use a special composition, such as "White Spirit".
3. If you have stained linoleum with fucorcin, do not get upset ahead of time. Bright crimson spots can be rubbed off. To do this, use a tooth powder. The composition must be combined with alcohol. Apply gruel to the stain and wait for it to solidify. Remove the tool and repeat several times.
4. You can use another no less effective way. To do this, you have to use the means for the toilet with chlorine. It is strongly recommended to pre-test. Otherwise, the caustic composition will permanently ruin the linoleum.

Practical advice

1. If at the time of the repair you showed the foresight and covered the linoleum with a special film in advance, then after the completion of the work, no special effort is required. Simply wash the floor with a special solution or soap and water.
2. Before any cleaning work, you must first sweep or walk on the linoleum with a vacuum cleaner. Otherwise abrasive particles on the floor can damage the coating.
3. There are special products for washing linoleum. Choose for yourself a suitable option from the proposed ones: “Mr. Proper”, “Domestos”, “Silit Bang”, etc.
4. Do not use for washing linoleum compounds that can deform the material. These include bleaching powder, other "hard" means of this type.
5. When the floor cleaning is complete, wipe it off with a dry microfiber cloth so that there are no stains left. Or leave the surface to dry on their own by opening the windows.

Before carrying out repairs, it is advisable to pre-cover the linoleum with a special construction film, which is sold in the appropriate store. If these actions have not been done, use the above methods.Consider how the mounting foam, primer, whitewash and cement mortar are removed from the surface of the linoleum.

Video: how to clean the apartment after repair