How to glue rubber boots at home

Rubber boots - the shoes necessary not only for giving, but also for the city. They protect against weather and dirt. But it has one drawback - any nail or a piece of glass is enough for shoes to become unusable. In the workshop such boots can not be given back, but it is a pity to throw them out. Therefore, many people prefer to repair their favorite shoes on their own.

How to care for boots

The rubber cover must be properly maintained. And then do not have to resort to their frequent repairs. After all, even high quality, which is guaranteed by the manufacturer, does not always mean safety of shoes.

Rubber boots need to be properly cleaned. Best of all, they are washed with a solution of glycerin and water. In this case, the boots should be wiped with a soft cloth and often dried so that the fungus does not appear. Wet rubber boots can not be dried with a hair dryer or battery.It is necessary that the shoes dry in natural conditions.

Tips before glueing the boots

In order to repair the boots was successful, and the shoes have served a very long time, you need to know the following:

1. Before repairing rubber shoes must be very thoroughly cleaned, washed and dried.
2. The patch can be cut from a tire or old rubber boots.
3. It is better to clean the patch from the inside out with an emery cloth or a file in order to make the surface rough for better adhesion of the glue.
4. It is best to degrease the surface of the shoe with acetone and solvent.
5. Glue you need to choose a special, which is necessarily indicated, for example, "shoe" or "rubber."
6. Before repairing rubber boots, it is imperative that you read the instructions from the glue manufacturer in order to do everything correctly.
7. It is best to smear the patch and bonding site with a special glue several times, after waiting until the first layer dries out a little.
8. When gluing the surface, it is necessary to press very strongly against each other or knock on the place of gluing with a hammer.
9. The patch on the boot can be easily disguised with emery cloth.

4 ways to glue rubber boots

Method 1. You can glue the boots with special glue. It can be purchased in stores for hunters and anglers. But in order to get the right glue, you need to know what exactly the shoes are made of. The fact is that for shoes made of EVA or polyurethane we need different adhesive compositions.

To help get the necessary glue can the seller, giving advice. Then everything is simple - you need to sand and degrease part of the boot and stick a patch. If the shoes are made of porous material, then you can glue it without using a patch. The edges at the place of the cut just need to turn out, grease it with plenty of glue and press it to each other.

Method 2 For this method, you will need a normal bicycle repair kit. It contains patches on special protective films, sandpaper and, of course, glue. The right place on the shoes clean sandpaper and degrease properly. Further, having previously removed the film from the bookmark, it is necessary to put glue on it and press the patch to the hole. You can use shoes almost immediately, but it’s better to wait at least for 12 hours.The only drawback of the method is an unaesthetic type of footwear after repairs.

If the hole does not appear on the topside, but on the sole, the gluing technology does not change. You just need to make the surface smooth and even, because usually the sole on such shoes is rather raised. This is possible with the help of a grinding machine. And only then stick a patch on this place.

But it is important to know that this patch will not last long, especially if the sole of the boots very often comes into contact with a rough and tough surface. Therefore, these boots are better to wear, for example, fishing. Well, if the sole is torn again, the gluing procedure will need to be repeated.

Method 3. In order to seal women's boots, without using patches, etc., it is necessary to purchase adhesive sealant. This can be done in any store for motorists. First you need to degrease the place of gluing, and then smear the torn edges with glue and press them together. If you do everything carefully, the boots will look like new.

Method 4. This method of repairing rubber shoes is also called the “hot” method. It is not complicated, but requires certain skills and, most importantly, a vulcanizer.As a patch, use rubber, pre-soaked in gasoline. It is placed on the hole in the boot and clamped with a vulcanizer. The device must be turned on for 20–30 minutes, then turned off and cooled down. Only after it cools, you can remove the press.

Do not despair if your favorite rubber boots suddenly torn. Enough to make a little effort and the repaired boots will not differ from the new shoes. You can use taped boots a day after the patch was applied. But if there is no time to wait, then you can walk in them in an hour.

Video: how to glue rubber boots with their own hands